Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Woodworking is the art that gets you busy and you can do this activity in the leisure time. If you are new to the art of woodworking there is nothing to worry about. It is not so much difficult that you cannot learn. Remember, learning never stops. So, have the courage to start the art of woodworking and take your time out to learn it. Here I am sharing 20 woodworking projects with you, have a look at them in detail. I am sure you would get some good ideas for the woodworking projects of your home and office. With these woodworking projects, the beauty of your drawing and dining room would be enhanced. You should not lose hope while learning these woodworking ideas. By the time you would learn these projects very easily; if you work hard and concentrate, you can go for the further more complex projects.
Make It: Paint four clothespins and a paper bowl red; paint two large wooden beads white. Glue eight thin 4-inch strips of red cardstock around the edge of the bowl to make legs; when dry, fold them in the middle for dimension. Glue the clothespins together as shown and adhere them to the front of the crab. Glue on the eyes and draw or cut out a mouth from black cardstock and attach. Complete the crab by punching a hole on each side; attach elastic cords to fit your child's head.
An excellent introduction to woodworking is to use crates as your main material. The boxes are already formed, which means less assembly work for you—yet it looks impressive once your project is altogether. With this crate coffee table, you still get to practice your skills adding the casters and the center box. Finish with a little stain, and this table is ready to roll. You can find the full tutorial at DIY Vintage Chic. 
The procedure is very easy to understand and follow for anyone with a little woodworking knowledge. Make sure to collect all the items you need before you start with the project. You may even ask Tracy your queries directly in the comment section of the tutorial post. Or you can ask them here. Either way, I hope that you manage to build this one nicely.
These 25 projects are absolutely stunning, to say the least. I would love to try out some of these designs all by myself and get started with some serious woodworking that I have been procrastinating for a long time. My favorites among these 25 are definitely the desk organizer, the bowling lane, and the tiered planter, but nevertheless, all are good in their own ways. I believe these projects only require hand tools and basic power tools like a rudimentary router and a jigsaw.
  Woodworking Pages     Deck Bench    Easels    Entertainment Centers    Firewood Racks    Fishing Rod Racks    Free Woodworking Catalog    Garages and Workshops    Garden Fence Gates    Greenhouses    Gun Cabinets    Houses    Hummingbirds    Index    Index for Resources    Kitchen Accessories    Lean To Sheds    Lumber Storage Racks    Marble Toys and Games    
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
×